Abstract The purpose of this study was to evaluate the effect of dentin moisture (moist and dry) on the bonding of fiber posts to root dentin with different adhesive strategies (etch-and-rinse, self-etch, and self-adhesive). Seventy-two extracted single-rooted human teeth were endodontically treated and divided into six groups (n = 12) according to the moisture of dentin surface and adhesive systems as follows: a) etch-and-rinse/moist, b) etch-and-rinse/dry, c) self-etch/moist, d) self-etch/dry, e) self-adhesive/moist, and 6) self-adhesive/dry. The specimens were sectioned into six slices for push-out bond strength (BS), nanoleakage (NL) by SEM, and Vickers microhardness (VHN) of the resin cement. A universal testing machine (AG-I, Shimadzu Autograph) was used at a crosshead speed of 0.5 mm/min until post extrusion, with a load cell of 50 kg for evaluation of the push-out strength. Data on BS, NL, and VHN were evaluated by two-way ANOVA and Tukey’s test (α = 0.05). Dentin moisture as the main factor was not significantly different for the push-out test. However, higher BS values can be observed for the etch-and-rinse group. A lower percentage of NL was found in the dry dentin groups. The moisture pattern was not significant in the hardness values for the pre-etching groups. Additional moisture did not increase the evaluated properties.

Abstract The purpose of this study was to analyze the effect of the application of different concentrations of EDTA on the adhesion of fiber posts to root dentin using self-adhesive resin cements. After endodontic treatment, 78 single roots were randomly divided into six groups (n = 13) according to the combination of the following factors: surface dentin treatment – control (distilled water), 17% EDTA and 24% EDTA; and self-adhesive resin cement - RelyX U200 (RX); and Multilink Speed (ML). After fiber post cementation, six slices were obtained for each root. Ten roots of each group were used for bond strength (BS) and three for microhardness (MH) evaluations. Data obtained from BS and MH tests for each resin cement were subjected to two-way ANOVA (surface treatment vs. root region) and to a post-hoc Tukey’s test (α = 0.05). The lowest BS value was observed in the 24% EDTA group for RX cement, whereas the highest values for ML cement were observed for the control group in the middle and apical regions. In the MH test, the lowest value for RX was observed for 24% EDTA in the cervical region, whereas and the highest value for the ML cement was observed in the control group. Regarding both self-adhesive resin cements tested, the application of 24% EDTA was not able to improve the adhesion of fiber posts to root canal.

Resumo Avaliar o efeito da combinação de ácido fluorídrico ou silano com o primer autocondicionante de cerâmicas sobre a eficácia da união imediata e após 1 ano de armazenamento em água, padrão de condicionamento e interação química desses tratamentos com o dissilicato de lítio. Um total de 16 blocos CAD/CAM de dissilicato de lítio (DL) foram cortados em quatro seções quadradas (n=64). Os espécimes de DL foram divididos em 4 grupos: 1) ácido fluorídrico a 5% + silano (HF + SI); 2) primer autocondicionante de cerâmica (MEP); 3) HF + MEP; 4) MPE + SI. Após cada tratamento, o sistema adesivo foi aplicado e as matrizes Tygon foram preenchidas com cimento resinoso dual (Variolink® II), seguido de fotopolimerização. Espécimes em forma de cilindro (0.8 mmÆ x 0.5 mm), foram armazenados em água (37 °C por 24h ou 1 ano) e submetidos ao teste μSBS (ANOVA dois fatores e teste de Tukey; a=0,05). Para avaliação das interações químicas por Espectroscopia Raman, os espécimes de DL foram divididos em 3 grupos (n=4): 1) sem tratamento (DL); 2) HF + SI; e 3) MEP. Para avaliação do padrão de condicionamento da superfície cerâmica após os tratamentos por MEV, os espécimes de DL foram divididos em 3 grupos (n=3): 1) DL; 2) HF; 3) MEP; e 4) HF + MEP. Ambos os métodos foram avaliados apenas qualitativamente. Não foi observada diferença significativa na μSBS imediata entre os grupos (p=0,73), mas após 1 ano de armazenamento das amostras em água, reduziu μSBS (p>0,0001). HF ou HF + MEP produziram uma maior dissolução da matriz vítrea do que o uso de MEP sozinho. Após a aplicação de SI e MEP, observou-se redução de ligações de siloxano, sugerindo o acoplamento da camada de silano na superfície do DL. O primer autocondicionante cerâmico pode ser uma alternativa ao tratamento cerâmico tradicional, uma vez que a interação química e a resistência de união a longo prazo, quando comparada ao tratamento tradicional foram estatisticamente semelhantes. A associação de ácido fluorídrico ou agente de acoplamento silano com um primer autocondicionante de cerâmicas não agregou nenhum benefício em termos de interação química e estabilidade.

Abstract To evaluate the effect of combining 5% hydrofluoric acid (HF) and silane (SI) with the self-etching ceramic primer on the immediate and after 1-year of water storage on bonding efficacy, conditioning pattern (CP) and chemical interaction (CI) to the lithium disilicate. A total of 16 CAD/CAM blocks of lithium disilicate (LD) were cut into four square sections (n=64). For bonding efficacy evaluation, the LD specimens were divided into 4 groups (n=10): 1) HF+SI; 2) self-etching ceramic primer (MEP); 3) HF+MEP; 4) MEP+SI. After each treatment, an adhesive system was applied and Tygon matrices were filled with a dual-cured resin cement followed by light curing. Cylinder specimens (0.8 mmx0.5mm) were stored in water (37 °C for 24 h or 1-year) and submitted to the μSBS test (2-way ANOVA and Tukey’s test; a=0.05). CP and CI were only evaluated qualitatively. No significant difference on the μSBS was observed between groups (p=0.73), but reduced μSBS was observed after 1-year of water storage (p>0.0001). After application of HF+SI and MEP, reduction in a number of siloxane bonds was observed, suggesting the coupling of SI on the LD surface. HF or HF+MEP produced a higher dissolution of the glassy matrix than the use of MEP alone. The MEP can be an alternative to traditional ceramic treatment once the chemical interaction and long-term bond strength were similar between both groups. The association of hydrofluoric acid or silane with a self-etching ceramic primer did not add any benefits in terms of chemical interaction and bonding stability.

Resumo: O objetivo deste estudo foi avaliar diferentes protocolos de condicionamento e a aplicação sônica/ultrassônica de uma resina infiltrante (RI) em lesões de mancha branca produzidas artificialmente (LMBA). As superfícies vestibulares/linguais de 48 molares foram induzidas à formação de LMBA e divididas em 6 grupos, de acordo com os protocolos de condicionamento e técnica de aplicação da resina infiltrante: ácido hidroclorídrico 15% (AH) + aplicação manual da RI; AH + ácido fosfórico 37% (AF) + aplicação manual da RI; AH + aplicação ultrassônica da RI (U); AH + aplicação sônica da RI (S); AF + AH + S; e AF + AH + U. para o grau de penetração (GP), condicionou-se as coroas com AH por 120 s. A RI Icon® (DMG) foi aplicada de acordo com as instruções do fabricante. As coroas foram coradas (rodamina B 0,1% por 12 h) e clareadas com peróxido de hidrogênio 30% por 12 h. os discos foram imersos em solução de etanol 50%, contendo 100 µM de fluoresceína sódica. O GP (em µm) foi mensurado por meio de microscopia confocal a laser (20´). A resistência de união (RU) foi calculada pelo teste de microcisalhamento (0,5 mm/min). Os dados foram submetidos ao teste ANOVA 2 fatores e Tukey (α=0,05). Para RU, a interação não foi significante (p>0,05). Para GP, os fatores principais foram significantes (técnica de aplicação - p<0,001; protocolos de condicionamento - p=0,003). A aplicação U mostrou os maiores valores de GP. AF+AH demonstrou resultados superiores ao grupo AH. As aplicações sônica/ultrassônica e o uso do ácido fosfórico antes do ácido hidroclorídrico aumentaram o GP da resina infiltrante. Os protocolos de condicionamento ou as técnicas de aplicação não influenciaram os valores de RU.

Abstract The aim of this study was to evaluate different conditioning protocols and sonic/ultrasonic application of an infiltrant resin (IR) in artificial white spot lesions (AWSL). the V/L surfaces of 48 molars were induced to an AWSL and divided in 6 groups, according to the conditioning protocols and application technique: 15% hydrochloric acid (HA) + manual application of the IR; HA + 37% phosphoric acid (PA) + manual application of the IR; HA + ultrasonic application (U) of the IR; HA + sonic application (S) of the IR; PA+HA+S; and PA+HA+U. For the Penetration Depth (PD), the crowns were etched with HA for 120s. The IR Icon® (DMG) was applied according to the manufacturer`s instructions. The crowns were dye penetrated (0.1% red fluorophore rhodamine B isothiocyanate for 12h) and bleached with 30% hydrogen peroxide for 12 h. The discs were immersed in a 50% ethanol solution, containing 100 µM of sodium fluorescein. The PD (in µm) was measured using confocal laser scanning microscopy (20x). The bond strength (BS) was performed by michoshear test (0.5 mm/min). Data were submitted to 2-way ANOVA and Tukey (α=0.05). For BS, the interaction was not significant (p>0.05). For PD, the main factors were significant (application - p<0.001; conditioning technique - p=0.003). The ultrasonic application showed the highest PD values. PA+HA presented higher results than HA. The sonic/ultrasonic applications and the use of phosphoric acid prior to hydrochloric acid improved PD of the infiltrant resin. Conditioning protocols or application techniques did not influence BS values.

ABSTRACT The objective of this work is to identify environmental and ecosystem services provided by trees from the perception of family farmers in the Serra dos Tapes, southern Rio Grande do Sul, Brazil, addressing the relevance of species for ecosystem sustainability of family farming. Environmental and ecosystem services offered by the tree flora of semi-deciduous submontane forest are presented according to the perception of farmers who use accumulated knowledge for social, cultural and economic reproduction in family farming. Four farmers were selected for their remarkable knowledge related to the agro-ecosystem and the local floristic composition, and they answered semi-structured interviews about 115 native tree species relating them to environmental and ecosystem services. The knowledge of farmers regarding the importance of forest cover for beekeeping, agroforestry system installation, source of biological materials for environmental recovery, conservation of hydric resources and for feeding mammals and birds was evidenced.

Resumo Analisar o efeito do co-iniciador alternativo 4,4’bisdimetilaminobenzidrol (BZN) no grau de conversão (GC) e nas propriedades mecânicas e biológicas de resinas compostas experimentais. O co-iniciador BZN foi utilizado em três concentrações (0,2, 0,5 e 1,2), e o co-iniciador DMAEMA como controle, nas mesmas concentrações acima. A concentração molar entre canforoquinona (CQ) e os co-iniciadores foi mantida constante (1:1). As resinas compostas foram manipuladas e submetidas aos testes de microdureza (VHN), resistência à compressão e flexural (em MPa), módulo de elasticidade (em GPa), GC (em %, por meio de espectroscopia micro-Raman e FTIR com KBr), citotoxicidade in vitro (frente às células fibroblásticas 3T3) das resinas experimentais. Os resultados foram submetidos ao teste ANOVA 1 fator e pós-teste de Tukey (α=0,05). As resinas compostas experimentais com o BZN apresentaram GC e propriedades mecânicas satisfatórias, além de serem consideradas atóxicas a fibroblastos 3T3. A inclusão do co-iniciador BZN à resina composta foi considerada não tóxica frente a células fibroblásticas 3T3 e sem comprometer o grau de conversão e as propriedades mecânicas da mesma.

Abstract To examine the effect of the alternative coinitiator 4,4’bis dimethylamino benzydrol (BZN) in degree of conversion (DC), mechanical and biological properties of experimental composites. The coinitiator BZN was used in three concentrations (0.2, 0.5 and 1.2%), and the coinitiator DMAEMA was used as control at the same concentrations as above. The molar concentration of camphorquinone (CQ) and coinitiators was kept constant (1:1). The composites were manipulated and submitted to microhardness test (VHN), flexural and compressive strength (in MPa), elastic modulus (GPa), DC (FT-IR) and in vitro cytotoxicity (against 3T3 fibroblastic cells) of the experimental resins. Data were subjected to two-way ANOVA and Tukey post-test (α=0.05). The experimental composite resin with BZN showed higher DC values compared to control DMAEMA groups. For the mechanical properties, microhardness values were higher in BZN groups; flexural strength and elastic modulus were similar between all the groups. Compressive strength for groups BZN0.5 and DMAEMA0.5 were not statistically different, being the lowest values attributed to group BZN0.2. The experimental resins with BZN and DMAEMA were considered nontoxic against 3T3 fibroblasts. The inclusion of the coinitiator BZN in experimental composites was considered nontoxic against 3T3 fibroblast cells, without compromising DC and mechanical properties.

Abstract Objectives To evaluate the influence of two curing techniques on the degree of conversion (DC) of resin cements and on bond strength (BS) of fiber posts in different regions of root dentin. Material and Methods Twenty single-rooted premolars were endodontically treated, and the post spaces were prepared. The roots were randomly divided into two groups (n=10), according to the activation mode of the resin cement RelyX™ U200 (3M ESPE Saint Paul, MN, USA): conventional (continuous activation mode) and soft-start activation mode (Ramp). The posts (WhitePost DC/FGM) were cemented according to the manufacturer’s recommendations and, after one week, the roots were cross-sectioned into six discs each of 1-mm thickness, and the cervical, medium, and apical thirds of the root canals were identified. The DC was evaluated under micro-Raman spectroscopy and the BS was evaluated by the push-out test. The data were analyzed by two-way ANOVA and Tukey’s test (α=0.05). Results Neither the activation mode nor the root regions affected the DC of the resin cement. Higher BS was achieved in the soft-start group (p=0.036); lower BS was observed in the apical third compared to the other root regions (p<0.001). Irrespective of the activation mode and root region, the mixed failure mode was the most prevalent. Conclusion The BS of fiber posts to root canals can be improved by soft-started polymerization. The DC was not affected by the curing mode.

Abstract Aim: To evaluate the effect of different in-office bleaching agents on the permeability, roughness and surface microhardness of human enamel. Methods: For evaluation of roughness and microhardness, 40 hemi-faces of 20 premolars were subjected to initial roughness (Ra parameter) and microhardness (VHN) measurements. Thirty-two premolar's crowns were used for permeability test. Then, all specimens were randomly divided into four groups: C - without bleaching (control), HP35 - bleaching with 35% hydrogen peroxide (HP), HPF38 - 38% HP+fluoride, HPC35 - 35% HP+calcium. Final roughness (FR) and microhardness (FM) measurements were evaluated. For permeability, the 32 crowns were immersed in 1% sodium hypochlorite (20 min) and silver nitrate solutions (2 h) and subjected to developing solution under fluorescent light (16 h). Three sections from the crowns were analyzed in light microscope (100x) to evaluate the scores of permeability: Score 0 - no tracer agent penetration; Score 1 - less than half the thickness of enamel penetration; Score 2 - tracer agent reaching half the enamel thickness; Score 3 - entire enamel depth penetration, without reaching dentin and Score 4 - tracer agent reaching dentin. For roughness and microhardness evaluation were used one-way ANOVA and Dunnet post-test for independent samples, and t test for paired samples. For permeability, the data were analyzed by Kruskal Wallis and Dunn tests. Results: A significantly higher permeability and surface roughness were observed in groups HP35, HPF38 and HPC35 compared to the C group, as well as decreased microhardness (p<0.05). Conclusions: All bleaching agents increased permeability and surface roughness, and decreased microhardness of human enamel; thus, the addition of fluoride or calcium was not beneficial.

Objetivo Avaliar a liberação e a capacidade de recarga de flúor de diferentes cimentos de ionômero de vidro, durante a simulação de desafio cariogênico. Material e método Foram confeccionados 12 corpos de prova para cada grupo experimental, com cimentos de ionômero de vidro convencionais – Maxxion R (FGM), Ketac Molar EasyMix (3M ESPE); cimento de ionômero de vidro modificado por resina – Vitrebond (3M ESPE), e resina composta, Filtek™ Z350XT (3M ESPE), como controle negativo. Os corpos de prova foram imersos alternadamente em sistema de ciclagem de pH, permanecendo 6 horas na solução de desmineralização e 18 horas na de remineralização, sendo mantidos em estufa a 37°C. Liberação de flúor foi verificada 1, 2, 7 e 14 dias antes e após a recarga com flúor, com eletrodo específico acoplado ao aparelho analisador de pH/fluoretos, calibrado a cada medição com soluções de fluoreto de sódio a 1 e 10 ppm, preparadas com TISAB II. Para leitura, foi adicionado 0,5 mL da amostra a igual volume de TISAB II. Recarga foi realizada com flúor neutro 2% por 4 minutos nas amostras, lavadas e imersas novamente nas soluções do sistema de ciclagem de pH. Os dados foram submetidos à análise de variância e ao teste de Tukey (α=0,05). Resultado A liberação inicial de fluoreto (μgF/cm2) foi de 45,36; 37,49, e 26,35 para Maxxion R, Vitrebond e Ketac Molar EasyMix, respectivamente. Diferenças estatísticas significativas entre os materiais foram verificadas antes e após a recarga (p=0,001). Após a aplicação tópica de flúor, os cimentos de ionômero de vidro apresentaram capacidade de recarga de flúor. Conclusão Cimentos de ionômero de vidro avaliados foram capazes de liberar flúor em soluções de ciclagem de pH e podem recarregar flúor através da aplicação tópica.

Objective To evaluated the ability to fluoride release and recharge in the different glass ionomer cements during simulation of cariogenic challenge. Material and method Twelve samples were made for each experimental group: conventional glass ionomer cements, Maxxion R (FGM), Ketac Molar EasyMix (3M ESPE); resin modified glass ionomer cement, Vitrebond (3M ESPE); and composite resin Filtek™ Z350XT (3M ESPE), negative control. The samples were immersed alternately in pH cycling method, remaining 6 hours in demineralization solution and 18 hours in remineralization solution and maintained at 37 °C. Fluoride release was measured 1, 2, 7, and 14 days before and after recharging with specific electrode coupled to the analyzer apparatus pH/fluoride, each measurement with calibrated solutions of sodium fluoride to 1 and 10 ppm, prepared with TISAB II. For reading was added 0.5 mL of sample to an equal volume of TISAB II. Recharging was made with neutral sodium fluoride to 2% for 4 minutes in the samples, washed and again immersed pH cycling solutions. Data were subjected to two-way ANOVA and Tukey’s post-hoc test (α = 0.05). Result The initial fluoride release (μgF/cm2) was 45.36 ; 37.49 and 26.35 for Maxxion R, Vitrebond and Ketac Molar EasyMix, respectively. Significant differences between the materials before and after recharging were observed (p=0.001). After topical application of fluoride, both showed ability to recharge. Conclusion The glass ionomer cements evaluated were capable of releasing fluoride in pH cycling solutions and may recharge through of a topical application.

O objetivo deste estudo foi investigar, in vitro, o efeito antibacteriano e a difusão frente ao E. faecalis, de novas medicações intracanal na superfície externa da raiz. As medicações testadas foram um gel placebo (PC), as novas formulações quer com nitrofurantoína a 3% (NIT) ou hidrocloridrato de doxiciclina a 3%(DX) e um gel de clorexidina a 2% (CHX) como controle positive. As novas formulações foram testadas usando o tradicional teste de difusão em agar (ADT) e um método de difusão adaptado (AADM), onde os dentes foram preenchidos com as medicações e deixados a difundir numa superfície de agar semeada com E. faecalis. No ADT, a maior área de inibição foi registada para DX, seguida por CHX e NIT. No teste AADM, apenas DX e CHX demonstraram ação antimicrobiana. Foram observadas diferenças significativas entre os grupos através do teste Kruskal-Wallis (X2=47.126; p<0.001). As novas formulações intracanais contendo DX e NIT demonstraram ação antimicrobiana quando em contacto com E. faecalis, mas apenas DX teve capacidade de difundir através dos túbulos dentinários e exercer ação antimicrobiana fora das raízes.

The aim of this study was to investigate in vitro the antimicrobial effect and diffusion against E. faecalis of new intracanal medications on the external root surface. The medications tested were a placebo gel (PC); the new formulations with either 3% nitrofurantoin (NIT) or 3% doxycycline hydrochloride (DX) and 2% chlorhexidine (CHX) gel as positive control. The new formulations were tested using the traditional agar diffusion test (ADT) and an adapted agar diffusion method (AADM), where the teeth were filled with the medications and left to diffuse on agar surface seeded with E. faecalis. In the ADT, the larger zones of microbial growth inhibition were seen in DX, followed by CHX and NIT. In the AADM test only DX and CHX showed antimicrobial effect. Statistically significant differences between groups were observed by the Kruskal-Wallis test (2=47.126; p<0.001). The new intracanal formulations with DX and NIT have demonstrated antimicrobial effect against E. faecalis, but only DX was able to diffuse through the dentinal tubules and exert antimicrobial effect outside the roots.

AIM: To evaluate the influence of finishing and polishing techniques on the surface roughness of two composite resins (CRs) subjected to bleaching procedure.METHODS: Forty-eight CR specimens were divided into six groups (n=8). For G1 to G3, a microhybrid CR (Opallis; FGM) was used, and G4 to G6, received a nanohybrid CR (Brilliant NewLine; Coltène/Whaledent). All specimens were subjected to bleaching procedure with 35% hydrogen peroxide (two 45-min applications, with a 5-day interval). The surface roughness of all specimens was evaluated before and after the bleaching and/or finishing/polishing (Ra parameter) by a roughness meter. After bleaching, the groups were subjected to finishing and polishing procedures: G2 and G5 - felt discs + diamond pastes; and G3 and G6 - silicon rubber tips. The control groups (G1 and G4) had no finishing or polishing treatment after bleaching. Data were analyzed by ANOVA and Tukey's post-test, and t test for paired samples (a=0.05).RESULTS: bleaching treatment increased Ra values for the nanohybrid CR specimens, but both finishing/polishing techniques were able to reduce these values; for the microhybrid specimens, only finishing/polishing with silicon rubber tips decreased the roughness values.CONCLUSIONS: For both microhybrid and nanohybrid CRs, the silicon rubber tips were effective to reduce the surface roughness after bleaching procedure.

This study compared the microleakage of class V restorations bonded with various one-step self-etching adhesives. Seventy class V resin-based composite restorations were prepared on the buccal and lingual surfaces of 35 premolars, by using: Clearfil S 3 Bond, G-Bond, iBond, One Coat 7.0, OptiBond All-In-One, or Xeno IV. The Adper Single Bond etch-and-rinse two-step adhesive was employed as a control. Specimens were thermocycled for 500 cycles in separate water baths at 5°C and 55°C and loaded under 40 to 70 N for 50,000 cycles. Marginal microleakage was measured based on the penetration of a tracer agent. Although the control showed no microleakage at the enamel margins, there were no differences between groups (p = 0.06). None of the adhesives avoided microleakage at the dentin margins, and they displayed similar performances (p = 0.76). When both margins were compared, iBond® presented higher microleakage (p < 0.05) at the enamel margins (median, 1.00; Q3–Q1, 1.25–0.00) compared to the dentin margins (median, 0.00; Q3–Q1, 0.25–0.00). The study adhesives showed similar abilities to seal the margins of class V restorations, except for iBond®, which presented lower performance at the enamel margin.

Esse estudo avaliou a influência do sistema de cimentação na resistência de união regional e os padrões de fratura de pinos de fibra à dentina radicular. As raízes de 48 incisivos humanos extraídos foram preparadas e divididas em 3 grupos (n=16) de acordo com o sistema de cimentação: AdperScotchbond Multi-Purpose + cimento resinoso RelyX ARC (SBMP+ARC); AdperSingle Bond 2 + RelyX ARC (SB+ARC) e cimento resinoso autoadesivo RelyX U100 (U100). Os pinos foram cimentados conforme as recomendações dos fabricantes para cada sistema de cimentação. Após uma semana, as raízes foram seccionadas transversalmente em 6 discos. Dois discos foram obtidos para os terços coronário, médio e apical e o teste de push-out foi realizado. O padrão de fratura foi avaliado em todos os espécimes. Os dados obtidos foram analisados através dos testes ANOVA dois fatores e Tukey. Quando o cimento U100 foi testado, não foram observadas diferenças significativas (p>0,05) entre as diferentes regiões radiculares. Valores de resistência de união significativamente superiores foram encontrados no terço coronário para SBMP+ARC e SB+ARC (p<0,05). O U100 apresentou significativamente mais fraturas mistas que o SBMP+ARC no terço apical (p<0,05). Conclui-se que o cimento resinoso autoadesivo RelyX U100 foi o único cimento não afetado pela região do canal radicular.

This study evaluated the influence of the cementation system on the regional push-out bond strength and failure pattern of fiber posts to radicular dentin. The roots of 48 extracted human incisors were prepared and divided into 3 groups (n=16), according to the cementation system: AdperScotchbond Multi-Purpose + resin cement RelyX ARC (SBMP+ARC); Adper SingleBond 2 + RelyX ARC (SB+ARC) and; RelyX U100 self-adhesive resin cement (U100). The posts were cemented as per manufacturer’s instructions for each cementation system. After 1 week, the roots were sectioned transversely into 6 discs. Two discs were obtained from the cervical, middle and apical thirds and the push-out test was carried out. The failure pattern was examined on all debonded specimens. The data were analyzed by two-way repeated measures ANOVA and Tukey’s test. When U100 was used, no statistically significant difference (p>0.05) was observed among the different root regions. Statistically higher push-out bond strength values were detected in the cervical third for SBMP+ARC and SB+ARC (p<0.05). The U100 showed significantly more mixed failures than SBMP+ARC in the apical third (p<0.05). In conclusion, the self-adhesive cement RelyX U100 was the only cement not sensitive to the root canal region.

El mantenimiento y el restablecimiento de la salud, función y estética son los objetivos principales de la odontología general. En los últimos años el aumento del interés por la estética en la sociedad se ha transformado en el principal motivo en la búsqueda de atención odontológica para una mejora de la apariencia dental y facial que permita alcanzar al paciente confianza, autoestima y respeto. Esto exige por parte del profesional conocimiento y experiencia en la aplicación de principios y referencias estéticas como guías para resolver los diferentes problemas que se presentan en la odontología restauradora actual. Este trabajo analiza los parámetros estéticos aplicados en odontología restauradora.

The maintenance and the reestablishment of the health, aesthetic and function are the primary targets of the general odontology. In the last years the increase of the interest by the aesthetic in the society has been transformed into the main reason in the search of attention for an improvement of the dental and face appearance that allows reaching to the patient confidence, self-esteem and respect. It demands on the part of the professional knowledge and experience in the application of references and aesthetic principles as it guides to solve the different problems that appear in restorative dentistry. This work analyzes the aesthetic references used in restorative dentistry.